Chemical Recycling of Carbon Fiber Reinforced Epoxy Composites Using Mild Conditions

The increased use of carbon fiber reinforced thermosets generates more waste and end-of-life products. However, an efficient recycling method for the expensive carbon fibers has not yet been developed. The selective decomposition of amine-cured epoxy resin under mild conditions is presented. A two-step method was investigated to decompose the epoxy resin. The optimum parameters were initially determined using a model compound. By analysis of the reaction products, a cleavage of the C–N bond according to the Cope elimination could be proven. Therefore, the Cope elimination is suggested as the main step of the decomposition of amine-cured epoxy resins in presence of hydrogen peroxide. By dissolving the resin, it is possible to recover resin-free fibers with unimpaired mechanical properties.     

Spark plasma sintering of B4C and B4C-TiB2 composites: Deformation and failure mechanisms under quasistatic and dynamic loading

Spark plasma sintering (SPS) was employed to consolidate powder specimens consisting of B₄C and various B₄C-TiB₂ compositions. SPS allowed for consolidation of pure B₄C, B₄C-13 vol.%TiB₂, and B₄C-23 vol.%TiB₂ composites achieving ≥99 % theoretical density without sintering additives, residual phases (e.g., graphite), and excessive grain growth due to long sintering times. Electron and x-ray microscopies determined homogeneous microstructures along with excellent distribution of TiB₂ phase in both small and larger-scaled composites. An optimized B₄C-23 vol.%TiB₂ composite with a targeted low density of ～3.0 g/cm³ exhibited 30–35 % increased hardness, fracture toughness, and flexural bend strength compared to several commercial armor-grade ceramics, with the flexural strength being strain rate insensitive under quasistatic and dynamic loading. Mechanistic studies determined that the improvements are a result of a) no residual graphitic carbon in the composites, b) interfacial microcrack toughening due to thermal expansion coefficient differences placing the B₄C matrix in compression and TiB₂ phase in tension, and c) TiB₂ phase aids in crack deflection thereby increasing the amount of intergranular fracture. Collectively, the addition of TiB₂ serves as a toughening and strengthening phase, and scaling of SPS samples show promise for the manufacture of ceramic composites for body armor.     

Effect of PDMS content on waterproofing and mechanical properties of geopolymer composites

The present study mainly studies the effect of polydimethylsiloxane (PDMS) content on the waterproofing and mechanical properties of geopolymer composites. Firstly, hydrophobic modified geopolymer composites (HM-GC) were prepared by adding PDMS during the mixing process. Secondly, the surface wettability characteristics, water absorption, uniaxial compressive and tensile properties of HM-GC were investigated. The effect of PDMS content on the waterproofing and mechanical properties was further discussed. Finally, considering the waterproofing and mechanical properties, the optimal PDMS content was proposed. The results showed that with increasing PDMS content, the contact angle of geopolymer composites rapidly increase at first and then stabilizes. The geopolymer composites with 4% and 5% PDMS content exhibit overhydrophobic surface wettability. In addition, the water absorption gradually decreases with increasing PDMS content, indicating an improvement in the waterproofing ability. The incorporation of PDMS can enhance the compressive properties of geopolymer composites while reducing the tensile properties. Comprehensively considering the waterproofing and mechanical properties, it is reasonable to select 4% as the optimal PDMS content used in practical marine engineering.     

Development and performance analysis of novel in situ Cu–Ni/Al2O3 nanocomposites

Cu–Ni/Al₂O₃ nanocomposite powders were manufactured using an in situ chemical reaction technique. This technique provides improved wettability and adhesion between the matrix and reinforcement phases. Aluminum nitrate, copper nitrate and nickel nitrate were used as start materials for the production of the composites. The powders were sintered in a hydrogen environment at 900 °C for 2 h after being cold pressed at 700 MPa. To determine the effect of Al₂O₃ on electrical and thermal conductivities and thermal expansion behaviors, the Cu–Ni matrix was supplemented with 3, 5, and 8 wt% Al₂O₃. The findings revealed that Al₂O₃ nanoparticles (20 nm) were dispersed uniformly throughout the copper-nickel matrix. Microhardness was improved from 53.3 HV for Cu–Ni matrix to 92.7 HV for Cu–Ni/8%Al₂O₃ nanocomposites. The electrical and thermal conductivities and thermal expansion coefficient were reduced as the amount of Al₂O₃ in the Cu–Ni matrix increased. The electrical conductivity was reduced by 38.7% by addition 5% Al₂O₃ nanoparticles to Cu–Ni matrix. The high interfacial bonding between Cu–Ni and Al₂O₃ nanoparticles was the main reason of the hardness improvement and maintaining relatively good electrical and thermal properties.     

Full and reduced-order H∞ filtering of Takagi–Sugeno fuzzy time-varying delay systems: Input–output approach

This article addresses the issue of delay-dependent H_∞ filtering design for TakagiŮSugeno fuzzy time-varying delay systems using the input–output approach. A three-term approximation model has been used to transform the original system into two interconnected subsystems. Since the nonquadratic Lyapunov–Krasovskii functional requires to deal with the membership function's (MF) time derivative, upper-bound inequalities have been added to the obtained conditions. Based on the scaled small gain theorem, nonquadratic Lyapunov–Krasovskii functional approach and considering the bounds of the MF time-derivative, the H_∞ full- and reduced-order filters are designed and then formulated in terms of linear matrix inequalities. Finally, illustrative examples are presented to demonstrate the validity of the proposed methods.     

Microstructure characterization and compressive performance of 3D needle-punched C/C–SiC composites fabricated by gaseous silicon infiltration

3D needle-punched C/C-SiC composites were fabricated from carbon fiber reinforced carbon (C/C) preforms, with densities of 1.05?g/cm³ and 1.28?g/cm³, by the gaseous silicon infiltration (GSI) method at fabrication temperatures from 1500?°C to 1800?°C. The compressive strengths and elastic moduli in transverse direction are larger than those measured under longitudinal compression except that samples fabricated from 1.28?g/cm³ density exhibit lower elastic moduli in transverse direction than in longitudinal direction. The compressive strength and modulus increase with fabrication temperature at 1500?°C and 1600?°C, and then decrease with higher fabrication temperature. Samples fabricated from the lower density C/C preforms have greater compressive strength and modulus. X-ray tomography was applied before and after the mechanical tests to characterize the microstructure and damage patterns, and the results indicated that for C/C-SiC composites fabricated at 1700?°C from 1.28?g/cm³ density C/C preform the matrix has a volume fraction (vol%) of 36.9%, and the initial intra-bundle cracks (0.6?vol%) display a space crossing structure while the inter-bundle pores (6.0?vol%) are special irregularly distributed.     

Utilization of linseed cake as a postagricultural functional filler for poly(lactic acid) green composites

Linseed cake (LC), a byproduct of linseed oil extraction, is used as a functional filler for production of biodegradable composites. To determine the influence of residual linseed crude oil contained in lignocellulosic filler on the properties of the poly(lactic acid) (PLA)-based composites with 5–30% filler content, two types of LC were analyzed: a defatted and an unmodified one. Complex analysis of the composites' properties change was conducted in relation to their structure modification caused by the addition of a waste filler. It was found that the addition of LC resulted in simultaneous plasticization and improved crystallization of PLA. Lignocellulosic particles and crude linseed oil contained in the LC powder provided a modifying effect, influencing the level of crystallinity and mechanical and thermomechanical properties. Using LC may thus overcome one of the main drawbacks of PLA, which is brittleness and low crystallinity. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47152.     

冲击载荷下TC18钛合金力学性能模拟研究

TC18钛合金在退火状态下的屈服强度非常高,进行动态力学性能测试存在一定困难,可优先考虑采用数值模拟方法对其动态力学性能进行研究,而数值模拟结果的精确性主要取决于合金本构方程的精确性。为了减少数值模拟与实验结果之间的差异,在Johnson-Cook模型的基础上做了调整,利用ABAQUS软件的子程序接口自定义了材料本构子程序UMAT,以代码的形式来扩展ABAQUS程序的功能。通过与ABAQUS/Standard软件分析结果以及实验结果的对比,验证了自定义材料本构子程序UMAT计算结果的精确性与可靠性。该研究可为TC18钛合金的结构设计提供参考。     

Gas‐phase removal of indoor volatile organic compounds and airborne microorganisms over mono‐ and bimetal‐modified (Pt,Cu, Ag) titanium(IV) oxide nanocomposites

The photocatalytic deactivation of volatile organic compounds and mold fungi using TiO₂ modified with mono‐ and bimetallic (Pt, Cu, Ag) particles is reported in this study. The mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide photocatalysts were prepared by chemical reduction method and characterized using XRD, XPS, DR/UV‐Vis, BET, and TEM analysis. The effect of incident light, type and content of mono‐ and bimetallic nanoparticles deposited on titanium(IV) oxide was studied. Photocatalytic activity of as‐prepared nanocomposites was examined in the gas phase using LEDs array. High photocatalytic activity of Ag/Pt‐TiO₂ and Cu/Pt‐TiO₂ in the reaction of toluene degradation resulted from improved efficiency of interfacial charge transfer process, which was consistent with the fluorescence quenching effect revealed by photoluminescence (PL) emission spectra. The photocatalytic deactivation of Penicillium chrysogenum, a pathogenic fungi present in the indoor environment, especially in a damp or water‐damaged building using mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide was evaluated for the first time. TiO₂ modified with mono‐ and bimetallic NPs of Ag/Pt, Cu, and Ag deposited on TiO₂ exhibited improved fungicidal activity under LEDs illumination than pure TiO₂.